how to wire i/o tilt pump

by jim
(clearwater fl, usa)

i bought a 1979 bayliner with small block 350 chevy engine, thr tilt/trim is paetially installed.
i am trying to figure out how to wire this single celonoid tilt motor to no avail;;

cant hook up my power trim

Can you help me hook up my trim switch to the solenoid and trim motor

Trim and Tilt - 2005 Yamaha

by Mark
(VA)

Motor is getting power, making the usual noise...but is not going up and down?

bayliner trim problems

I have a 2006 bayliner 175 and the trim will not move up or down and it makes no noise. The battery is good because the boat will turn over. I recenty had it worked on could they have forgotten to plug something back up.

power trim

I HAVE A 1982 MERCRUISER 140MP THE POWER TRIM IS NOT WORKING IS THERE A WAY TO RAISE IT MANUALLY. MY E-MAIL ADDRESS IS SABRES@PEOPLEPC.COM

Power trim issue

When sitting on the trailer my 2008 Evinrude 250 HO E-tec will not stay trimmed up. It gradually drops. This is the first time I've noticed that happening. It has been very cold here and we've had a very drastic temperature change from very cold to the high 50's. What is causing this and what's the remedy. Thanks

cajun power tilt hydraulic

i have a 90 cajun bass boat the hydraulic cylinder for the tilt has bust a seal can that be fixed or is it cheaper to get a new hydraulic????????//

Power Trim Gauge Not Functioning

I HAD THE POWER TRIM UNIT REPLACED LAST YEAR. AFTER PUTTING THE BOAT IN THE WATER I NOTICED THE TRIM GAUGE WAS NOT FUNCTIOING. COULD IT BE SIMPLY A BLOWN FUSE?

Tilt and trim beep them motor died

by Jerry
(Cedar Creek Lake Texas)

Mercury 115 efi 4 stk running across the lake trimmed the motor it gave a really loud beep and the motor died. Trim won’t operate from switch or motor ...... turn the key I got nothing except my gas gauge goes to full....

Motor won't trim up

by Kim Robinson
(Sandersville, Ms.)

I was fishing the other day and all of a sudden the motor would not trim up. It makes no sound when I try to get it up but when I do it down it makes a sound as though it is going down but it is all the way down. What can I do to get it up. It is a 50 hp mercury motor. thanks, Kim

tilt is not working

by chris
(Aurora, OH)

I have a 1977 sea ray 19' 190hp... tilt motor went down wont come back up... Changed the selinoids both.... Was told it was a bad motor.... Does this motor control both the tilt and trim??? And were is it located?? Is it a tough job?? thank u....

chris

power trim problem-

by ed
(wpg)

Trimed my 1984 90hp yamaha all the way up on weekend and now it wont go down. Someone said the cylinder may be low on oil.Is this possible? How do I check he also said there should be a bleeder valve but I cannot find it

Trim motor stuck in down

by Aaron taylor
(Bryant al)

I was running down river and hit big yaght waves and my boat came out of the water and hit hard but when it did my trim went completely to down position and hung there. The trim motor would not stop or go off no matter the buttons i touched and im afraid it almost burned my motor up by the time i made it back to dock.cod it be the selinoid or relays

power trim stuck and trim only down will not trim up

by don
(georgetown, ky)

My evinrude 150 outboard motor has the trim stuck in the down run mode will not trim up. I can hit the up button and it will stop the downward trim but will not run the up trim.

Tilt/trim - trims down fine but very slow to trim up.

by Brian
(Pierre Part, La.)

Can you tell why my boat motor tilt/trim will trim motor down at normal speed but very slow to trim up sometimes it will not trim up at all. I can hear its motor working.Could it be level of hydralic oil and if so how can I check it and add to it. If not what else could it be?

want to add a tilt / trim gauge

by Rich
( Minnesota)

I want to add a tilt / trim gauge to my 1990 18' open bow maxum 3.0 alpha 1 out drive, need to know were the wires are or were to hook up the wires from gauge??